Prentke Romich Company
http://www.prentrom.com/support/article/1501
Kit includes:
3 Screen Protectors
60 or 84 Location Touchguide
Squeegee/Scraper
You Will Need a spray bottle of water and a lint-free cloth.
The Screen Protector fits on top of the display screen to protect the display from spills, saliva, food, etc. It can be used alone or under a Touchguide.
The Touchguide fits over the display screen of your device. As you move your finger over it, the small holes help to guide your finger to the key you want.
*Before You Begin: If your display screen is dirty, spray Windex™ or a flat-screen TV cleaner onto a lint-free cloth like the static cloths used to clean flat screen TVs and computer displays. Clean the display by wiping the damp cloth over it.
To Use a Screen Protector
Note: Although the ECO is shown, the instructions are the same for installing on a Vantage.
· Turn your device OFF and lay it flat on a table.
· Now, very lightly mist the display screen with water, Windex or a flat-screen TV cleaner. You want only a very thin mist which you will leave on the screen.
|
· The mist on your display should allow you to slide the Screen Protector around until you have it positioned so it covers your display from corner to corner.
· Use the squeegee card that came in your kit to smooth out the protector. You want to get any wrinkles and air bubbles out. Some of the mist will drip out. This is all right. You will wipe it off in a minute.
· When the protector is smooth, take the static or lint-free cloth and thoroughly dry the protector, the edges around the display screen and the device case.
· Let your device air dry completely before turning it on (5 minutes or so).
To Remove the Screen Protector
Carefully peel back one of the corners of the Screen Protector and then gently pull it off your display screen.
To Clean/Disinfect the Screen Protector
Turn your device OFF.
If the Screen Protector is extremely dirty, just remove it and follow the directions above to place a new protector on the display.
If it just needs to be wiped off, mist it lightly with water or a glass cleaner and wipe it off with a static cloth. If you are using a Touchguide with the protector, remove the Touchguide before cleaning the Screen Protector.
To Use the Touchguide with Vantage Plus
Because the Vantage Plus case is older and designed differently from the Vantage Lite and ECO2, you must bend the two center tabs in order for the Touchguide to stay in place.
· You will need a straight-edge implement, such as a sturdy ruler, a putty knife, a larger flat-head screwdriver, etc.
· Place the straight-edge against one of the center tabs. Lift the bottom of the Touchguide UP against the straight-edge and push/pull until you get a crease in the tab.
· Once you get a crease in the tab, you can finish by laying the Touchguide back down and pushing the tab against the straight-edge with your finger so that it is bent straight up. Repeat with the other center tab.
Now you are ready to put the Touchguide on your Vantage Plus.
*Below is one way to seat the Touchguide. You may find a way that works better for you. The point is to try to keep the Touchguide centered on your device so the holes line up well with the communication area you will be using.
· Turn your device OFF.
· Remove protective film over Touchguide.
· One side of the Touchguide has smoother edges around the circles than the other side. You want the smooth-edged side face-up on your device.
· Tuck the top and bottom tabs on the left side of the Touchguide into their slots, then slide the Touchguide to the left to seat it properly.
· Slide the right bottom tab in place.
· Now slide the right top corner in place.
· Fit the two bent tabs so they are flush against the case. These tabs will hold the guide in place.
· The installed Touchguide.
To Remove a Touchguide
Put your fingers on the edges of the two u-holes at the top of the guide and pull down and out on them until the tabs pop out of their slots. You can also carefully slide a small screwdriver or unbent paper clip under the small notch at the top of the guide and lift up to pop the top tabs out.
To Clean a Touchguide
Remove the Touchguide from your device. Wash it in hot, soapy water. Rinse well and dry with a soft cloth. Make sure the Touchguide is completely dry before putting it back on your device.
To Disinfect a Touchguide
Remove the Touchguide from your device. First, wash the Touchguide in hot, soapy water. Then mix ¼ cup vinegar with 1 cup water. Wipe the Touchguide with a cloth dampened with the vinegar and water mixture. Allow the Touchguide to air dry. Make sure it is completely dry before putting it back on your device.
