Prentke Romich Company
http://www.prentrom.com/support/article/1500

Installing the Screen Protector and Touchguide on ECO.

In the Kit

3 Screen Protectors

144 Location Touchguide

Squeegee/Scraper

You Will Need a spray bottle of water and a lint-free cloth. 

The Screen Protector fits on top of the display screen to protect the display from spills, saliva, food, etc.  It can be used alone or under a Touchguide.

The Touchguide fits over the display screen of your device. As you move your finger over it, the small holes help to guide your finger to the key you want.

*Before You Begin: If your display screen is dirty, spray Windex™ or a flat-screen TV cleaner onto a lint-free cloth like the static cloths used to clean flat screen TVs and computer displays. Clean the display by wiping the damp cloth over it.

To Use a Screen Protector  

·         Turn your device OFF and lay it flat on a table.

·         Now, very lightly mist the display screen with water, Windex or a flat-screen TV cleaner. You want only a very thin mist which you will leave on the screen.

• Peel the Screen Protector from its cardboard holder and lay it on your display screen. The side that was against the cardboard is the side that should be placed against the screen.

·         The mist on your display should allow you to slide the Screen Protector around until you have it positioned so it covers your display from corner to corner.

• Place protector on display and move into position

·         Use the squeegee card that came in your kit to smooth out the protector. You want to get any wrinkles and air bubbles out.  Some of the mist will drip out. This is all right. You will wipe it off in a minute.

·         When the protector is smooth, take the static or lint-free cloth and thoroughly dry the protector, the edges around the display screen and the device case.

·         Let your device air dry completely before turning it on (5 minutes or so).

To Remove the Screen Protector

Carefully peel back one of the corners of the Screen Protector and then gently pull it off your display screen. 

To Clean/Disinfect the Screen Protector

Turn your device OFF.

If the Screen Protector is extremely dirty, just remove it and follow the directions above to place a new protector on the display. 

If it just needs to be wiped off, mist it lightly with water or a glass cleaner and wipe it off with a static cloth. If you are using a Touchguide with the protector, remove the Touchguide before cleaning the Screen Protector.

To Use the Touchguide with ECO2

Below is one way to seat the Touchguide. You may find a way that works better for you. The point is to try to keep the Touchguide centered on your device so the holes line up well with the communication area  you will be using.

·      Turn your device OFF.

·      Remove protective film over Touchguide.

·      One side of the Touchguide has smoother edges around the circles than the other side. You want the smooth-edged side face-up on your device. 

·      There are small tabs around the edges of the Touchguide

·      Tuck the top and bottom tabs on the left side of the Touchguide into their slots, then slide the Touchguide to the left. 

·      Now tuck the top and bottom tabs on the right side into their slots.

·      Center the Touchguide and then tuck in the bottom center slot. 

·      Run your palm over the Touchguide to smooth it down on the display screen and to make sure it is securely seated so far.

·      Place your middle fingers in the U-holes at the top of the guide.  The sides of your hands should help hold the Touchguide in place.

·      Use your index fingers  and  tuck the top center tabs into place.

To Remove a Touchguide

Put your fingers on the edges of the two u-holes at the top of the guide and pull down and out on them until the tabs pop out of their slots.  You can also carefully slide a small screwdriver or unbent paper clip under the small notch at the top of the guide and lift up to pop the top tabs out. 

To Clean a Touchguide

Remove the Touchguide from your device. Wash it in hot, soapy water. Rinse well and dry with a soft cloth. Make sure the Touchguide is completely dry before putting it back on your device.

To Disinfect a Touchguide

Remove the Touchguide from your device. First, wash the Touchguide in hot, soapy water. Then mix ¼ cup vinegar with 1 cup water. Wipe the Touchguide with a cloth dampened with the vinegar and water mixture. Allow the Touchguide to air dry. Make sure it is completely dry before putting it back on your device.